Product

bs1449 mechanical properties

bs1449 mechanical properties

bs1449 mechanical properties

BS 1449 HR 3 - BEBON steel

BS 1449 HR 3 steel plate/sheet, under BS 1449 standard, we can regard HR 3 steel plate/sheet as stamping and cold forming steels. HR 3 steel is mainly used as stamping and cold forming steels. BS 1449 HR3 steel plate/sheet is stamping and cold forming steels, it is suitable for non-structural presswork and forming.This jind of steel is identical to UNI:NFA 36-301 ,DIN:DD11.JIS:SPHD,BS:HR3 and so on. BS 1449:1956 - Specification for steel plate (not Extension of BS 970. Section 1:manufacture, methods of testing, tolerances on dimensions. Section 2:chemical composition, mechanical properties for each steel. En 21, En 42, En 43 and En 44 types only.

CS70,MILD STEEL CS1 AND CS4 STRIP Sales Office Tel:Fax

BS EN 10132-4 supercedes BS 1449 BS EN 10139-DC04 BS EN 10139-DC01 Shearing sizes 0.203mm to 3.251mm Width range 3.00mm to 300mm Chemical composition (%) steel type C min C Max Si Min Si Max Mn Min Mn Max S Max P Max CS1 mild steel - 0.08 - - - 0.45 0.030 0.025 CS4 mild steel - 0.12 - - - 0.60 0.050 0.050 CS70 70 carbon 0.65 0.75 0.05 0.35 0.50 CS80 - AISI 1075 - 1.2003 - AISI 1075 - BSS Steel StripCS80 is a spring steel grade within BS1449. It is a close equivalent to C75S and AISI /SAE 1075, and closely matches EN42. CS80 is usually supplied in the hardened and tempered condition. It is widely used for the manufacture of flat springs, knives and blades. It has gained popularity in recent years, as whilst it was notoriously difficult to cut, the advent of laser and water jet cutting techniques have CS80 Spring Steel - Delivered Nationwide by West Yorkshire West Yorkshire Steel are suppliers and stockholders of sheet, strip and plate conforming to BS1449 and BS5770 designations. This grade is a carbon spring steel with an average carbon content of 0.80%. When supplied in coil it can be cut and slit to your requirements. It is common for CS80 strip to be supplied with a polished surface finish; this is achieved by a fine grinding, abrasive brushing or other

DC01 / 1.0330 - SteelNumber - Chemical composition

Mechanical properties of steel DC01 (1.0330) Rm - Tensile strength (MPa) 270-410:ReH - Minimum yield strength (MPa) 280:A - Min. elongation Lo = 80 mm (%) 28:A - Min. elongation Lo = 5,65 So (%) (+A) 32:Vickers hardness ( HV):(+A) 105 :Equivalent grades of steel DC01 (1.0330 Generic MMPDS Mechanical Properties TableDec 06, 2014 · Because these directions have a significant impact on the mechanical properties. If a part is manufactured using this rolled plate, the properties depend on the grain direction that the critical part feature lies along. A common example would be lugs or fittings machined from this plate. Now let us dig into the properties table itself. Steel Equivalent Table - Old Engine HomepageChemical Composition :Mechanical Properties :Related Specifications :General Information :C :Si :Mn :Ni :Cr :Mo :Va :S :P :Tensile Strength :Yield

UK B.S. HR4, BS 1449-1-1.2, - Steel grades, Properties and

This page cover the Mechanical Properties, Chemical Element, Cross Reference of UK B.S. HR4 steel grade, Application Steel plate, sheet and strip. Carbon and carbon-manganese plate, sheet and strip. Specification for hot rolled steel plate, sheet and wide strip based on

Contact us

Email: [email protected]